Electronic Ignition Conversion Kit
for
Chris-Craft
Prestolite or Delco Marine Distributors
for Non-Vacuum-Advance Prestolite or Delco Distributors
(Please specify whether for Prestolite or Delco distributor)
Replaces Points and Condenser - Never Adjust Points or Timing Again!
The Hot-Spark electronic ignition conversion kit replaces breaker points and condenser in the distributor to provide rock-solid reliability. With the Hot-Spark electronic ignition, dwell and timing are always spot-on accurate.
No matter how strong your engine is, you won't get the most out of it without a good spark. The stock, points-based ignition system used technology that dates back a century - to the Kettering system, which was introduced in the 1910 Cadillac. Even though you can adjust breaker points for near-electronic ignition performance, they will burn and wear within a few thousand miles, long before the recommended replacement interval. With points, the timing will drift; power and fuel economy will suffer.
The Hot-Spark electronic ignition conversion kit delivers a strong spark every time and is maintenance-free. You'll notice quicker starts, more top end power and a little gas mileage boost. It's as easy to install as points and condenser!
Advantages of the Hot-Spark electronic ignition conversion kit:
Replaces points and condenser with solid-state electronics
Set it and forget it - Never adjust points and timing again!
Zero maintenance
Delivers far more voltage to the spark plugs than points-based points
Reliable Hall-effect technology
Never gets out of adjustment
Rock-steady reliability
Dwell and timing are always spot-on accurate
Increased gas mileage, fuel economy
Quick starting
Smooth idling
Cleaner emissions
Longer spark plug life
Longer engine life
Cleaner engine oil due to less unburned fuel
Longer interval between oil changes
Easy to install - If you can install points, you can install the Hot-Spark electronic ignition conversion
No points to wear, burn, pit or corrode
No condenser needed
Absolutely no points float - zero - even at redline RPM and beyond!
Never worry about drifting dwell or timing again
No rubbing parts - nothing to wear out!
Fits completely under the distributor cap
Stealth modification - maintains stock appearance
Includes everything you need, no external ignition box required.
Works with stock distributor and coil
Encased in high-temp thermoplastic - protected from the elements and oil, grease, dirt, water, etc.
Never bother with points or condenser again!
The best investment you'll ever make for your vehicle
Saves precious ($$$) fuel
8-cylinder distributors require a coil with a minimum of 1.5 Ohms or more primary resistance or HS15HEC high-energy coil.
Requires a 12-volt, negative ground electrical system.
How many miles until the Hot-Spark electronic ignition conversion kit pays for itself? Click here
Three-year replacement warranty
3DEL4U1 - For 4-Cylinder Delco Non-Vacuum-Advance Distributor with Screw-down Distributor Cap
3PRE8U1 - For 8-Cylinder Prestolite Non-Vacuum-Advance Distributor with Clip-down Distributor Cap
3PRE8U2 - For 8-Cylinder Prestolite Non-Vacuum-Advance Distributor with Screw-down Distributor Cap
Chris-Craft
1975-80 4-cyl FL181, FL153 - Delco Distributor - 3DEL4U1
1963-71 8-cyl All models - Prestolite Distributor IBM-4115, IBM-4116 - 3PRE8U1
1981-85 8-cyl All models - Prestolite Distributor IBM-7013 - 3PRE8U2
International Buyers – Please Note:
Import duties, taxes and charges are not
included in the item price or shipping charges. These charges are the buyer's
responsibility.
Please check with your country's customs
office to determine what these additional costs will be prior to
bidding/buying.
|
Hot-Spark Electronic Ignition Conversion Kit for 8-cylinder Prestolite Distributors without Vacuum Advance, with Clip-down Distributor Cap |
|||||||||||||
|
Easy to Install - Replace Points and Condenser with Solid-State Electronics |
Electronic Ignition Conversion Kit. Replaces points and condenser in 8-cylinder Prestolite non-vacuum-advance distributors with clip-down distributor cap.
|
||||||||||||
|
|||||||||||||
|
Hot-Spark Electronic Ignition Conversion Kit for 8-cylinder Prestolite Distributors without Vacuum Advance, with Screw-down Distributor Cap |
|||||||||||||
|
Easy to Install - Replace Points and Condenser with Solid-State Electronics |
Electronic Ignition Conversion Kit. Replaces points and condenser in 8-cylinder Prestolite non-vacuum-advance distributors with screw-down distributor cap.
|
||||||||||||
|
|||||||||||||
|
1.7 Ohms primary resistance 11K Ohms secondary resistance |
||||||||||||
|
High secondary resistance for more voltage at the plugs Ideal for Use with Hot-Spark 6- and 8-cyl Electronic Ignition Conversion Kits with red 3-series ignition module |
Heavy-duty, high-energy coil with extra turns of copper wire in the
secondary windings for as much as 45,000 volts to the spark plugs - more turns
of copper wire than other standard-sized canister coils - twice as much as many
other coils.
Application:
For 6- and 8-cylinder (3-series) electronic
ignition conversion kits
Designed specifically to produce maximum spark
when used
with Hot-Spark red electronic ignition conversion kits
(red ignition module).
Also for points-based ignition systems
Epoxy-filled
canister (not oil-filled) to withstand high-vibration
environments
Rugged, mirror-polished case -
won't chip or peel like chrome-plated coil canisters.
Standard 56mm (2.2 in.) coil
diameter - fits stock coil clamps.
In Stock:
Available:
|
|||||||||||
|
||||||||||||
|
Hot-Spark Electronic Ignition Conversion Kit for 4-cylinder Delco non-vacuum-advance Distributors |
|||||||||||||
|
Easy to Install - Replace Entire Breaker Plate with Solid-State Electronics |
Electronic Ignition Conversion Kit. Replaces points and condenser in many 4-cylinder, Delco centrifugal-advance distributors.
|
||||||||||||
|
|||||||||||||
|
3.4 Ohms primary resistance 11K Ohms secondary resistance |
||||||||||||
|
High secondary resistance for more voltage at the plugs Ideal for Use with Hot-Spark 4-cyl Electronic Ignition Conversion Kits with red 3-series ignition module |
Heavy-duty, high-energy coil with extra turns of copper wire in the
secondary windings for as much as 45,000 volts to the spark plugs - more turns
of copper wire than other standard-sized canister coils.
Application:
Ideal for 4-cylinder distributors. Provides more primary resistance to protect from
overheating due to high-voltage or high-temperature environments.
Designed specifically to produce maximum spark
when used
with Hot-Spark red electronic ignition conversion kits
(red ignition module). Also excellent for points-based
distributors - high primary resistance helps reduce points burning, pitting.
Epoxy-filled
canister (not oil-filled) to withstand high-vibration
environments
Rugged, mirror-polished case -
won't chip or peel like chrome-plated coil canisters.
Standard 56mm (2.2 in.) coil
diameter - fits stock coil clamps.
In Stock:
Available:
|
|||||||||||
|
||||||||||||
|
Hot-Spark Electronic Ignition Conversion Kit for 4-cylinder Delco non-vacuum-advance Distributors |
|||||||||||||
|
Easy to Install - Replace Points and Condenser with Solid-State Electronics |
Electronic Ignition Conversion Kit. Replaces points and condenser in many 4-cylinder, Delco centrifugal-advance distributors.
|
||||||||||||
|
|||||||||||||
Foreign Orders: Shipping discount available if purchasing multiple items.
Click here for Hot-Spark Ignition Installation Instructions
Just a better idea. TM
